Accéder au contenu principal

Réfléchir !

C'est un conseil que je donne aux personnes, au cours de multiples conversations... "Ne jamais cesser de réfléchir".
Au fil des temps, j'ai pu reformuler ce conseil, avec mon expérience des réflexions des gens qui m'entourent... J'ai ainsi créé un autre conseil, qui peut être aussi un argument, ou un contre-argument, etc.
Je ne suis pas certain d'être le premier à le formuler, mais c'est un résultat fondamental de mes pensées :


"Lorsqu'on te demande d'arrêter de réfléchir, c'est le moment de commencer la réflexion !"


Comment alors j'explique ce conseil ? facile, simple et élégant. La chose la plus précieuse que l'homme a inventé, c'est la connaissance, et plus particulièrement la science. L'accumulation des théories (attention : une théorie ne signifie pas juste une idée, mais toute vérité qu'on peut tester, ou précisément : "une théorie est un ensemble d’affirmations dont certaines sont des axiomes et les autres des théorèmes démontrables à partir de ces axiomes et au moyen de règles de logique [Wikipedia]") est la connaissance. Mon principe cité ci-dessus est pragmatique et très efficace pour évoluer.


Plus réaliste cette fois, je dis aussi que les tabous nous empoisonnent de plus en plus. Rien ne nous offre une certitude, sauf la réflexion. Ceux qui ont peur de se poser des questions (et les questions n'ont pas toujours une réponse) n'évolueront jamais.


Je dis parfois que l'audace et le courage sont plus précieux que l'intelligence. Mais pour le prouver, j'ai besoin du temps, pour écrire un autre post dédié.

Commentaires

Posts les plus consultés de ce blog

GNS3: Simulating a 100% opensource site2site VPN using Wireguard, VyOS and OpenVSwitch

 This is something I had in mind but didn't find the time to accomplish before. It just took a very cold day to convince me that I have to play with Wireguard on VyOS. I used GNS3 of course, on my personal Linux laptop to create this setup. Of course the performance was not that great since it is just a simulation.  In real life, I am using Wireguard on a 10 years old Raspberry Pi Model B and amazingly with just a 700MHz single core ARM CPU and less than 512 MB of RAM I had a decent and stable permanent Wireguard tunnel. (My bandwidth would reach 24 Mbps without issue) Back to my simulation, this is what it looks like : Quick explanation: the VYOS routers labeled IPERF1 and IPERF2 are only used for an iperf3 test, which was able to reach about 50 to 60 Mbps each time. It ain't much but it was honest (and free) secure bandwidth! I won't get into the details of this setup but I will just post the two most important configurations : R-East and R-West : #### VYOS WireGuard Site...

GNS3 on Manjaro/Arch Linux: How to create virbr0 for NAT to work

Problem: You can't add a NAT connection to your GNS3 simulation, and you get the error : "ERROR template_manager:226 Error while creating node from template: NAT interface virbr0 is missing, please install libvirt" Steps to resolve: 1- Create a file named /tmp/default.xml 2- Paste this content and save: <network>   <name>default</name>   <bridge name="virbr0"/>   <forward mode="nat"/>   <ip address="192.168.123.1" netmask="255.255.255.0">     <dhcp>       <range start="192.168.123.2" end="192.168.123.254"/>     </dhcp>   </ip> </network> 3- Execute the following commands in your shell : virsh net-define /tmp/default.xml sudo virsh net-start default sudo virsh net-autostart default  

AutoWG: a simple Bash script to connect two devices with Wireguard

 I made today a quite simple BASH script that allows to connect two devices running Wireguard (tested with Debian Linux 12, but should work with any device) You can check it out (and fork it if you want) in this Gitlab Page This is the source code as of now, but I could modify it later (any suggestions are welcome) : #!/bin/bash # # AUTOWG written by Hamdi KADRI  # No copyright in any form or kind # This script is intended to create configurations for  # a point-to-point Wireguard connection between a server # and a client (/30 network) # # Step zero: declare configurations as variables servercfg="[Interface] Address = <serverwgIP> SaveConfig = true ListenPort = <port> PrivateKey = <server-privatekey> [Peer] PublicKey = <client-pubkey> AllowedIPs = <clientwgIP> " clientcfg="[Interface] PrivateKey = <client-privatekey> Address = <clientwgIP> [Peer] PublicKey = <server-pubkey> AllowedIPs = 0.0.0.0/0 EndPoint = <serverIP...